PCB design board Texas Instruments BQ24113EVM Stockists

The Texas Instruments bq24113EVM is the evaluation module (EVM) for the bq24113 Li-Ion charge management IC. The bq24113 is a highly integrated battery charge IC utilizing synchronous switch mode power conversion for efficient and comprehensive charge control of a single or two series cell Li-Ion battery. The EVM is a complete bq24113 based circuit and provides a convenient method to evaluate the operation and performance of the IC.


Bargain Price: £72.99

PCB design board Texas Instruments BQ24113EVM Deals on eBay PCB design board Texas Instruments BQ24113EVM Deals on Amazon
StockistProductPrice 
BargainplacePCB design board Texas Instruments BQ24113EVM£72.99Visit Store


PCB design board Texas Instruments BQ24113EVM Related Products:

 
 

PCB design board Texas Instruments THS4062EVM

The THS4062 dual high-speed amplifier evaluation module (EVM) is a complete dual high-speed amplifier circuit. It consists of the THS4062 dual high-speed amplifier IC, along with a small number of passive parts, mounted on a small circuit boad measuring approximately 1.9 inch by 2.2 inch. The EVM uses standard SMA miniature RF connectors for inputs and outputs and is completely assembled, tested, and ready to use - just connect it to power, a signal source, and a load (if desired).

PCB design board Texas Instruments THS4062EVM on eBay PCB design board Texas Instruments THS4062EVM on Amazon

 
 

PCB design board Texas Instruments XILINXPWR-081

Single-Channel Linear Regulator Power Management Solution Providing ICCINT up to 1.4 A from VIN= 3.3 V and 800 mA from VIN= 5.0 V

PCB design board Texas Instruments XILINXPWR-081 on eBay PCB design board Texas Instruments XILINXPWR-081 on Amazon

 
 

PCB design board Texas Instruments BQ24600EVM

Evaluation Module for bq24600/bq24620/bq24640. the bq24600 is a highly integrated Li-ion or Li-polymer switch-mode battery charge controller. The bq24620 is highly integrated switch-mode battery charge controller designed specifically to charge Lithium Phosphate battery chemistries.

PCB design board Texas Instruments BQ24600EVM on eBay PCB design board Texas Instruments BQ24600EVM on Amazon

 
 

PCB (unequipped) Texas Instruments LMH730216/NOPB

Texas Instruments offers this unpopulated Evaluation Board to aid in the evaluation and testing of high-speed Op Amps that are offered in the 5-/6-pin SOT-23 package. Resistors, capacitors, or any other surface-mount components can be easily mounted on this board in the desired circuit configuration. The performance can then be evaluated under the test conditions of your choice. Power supplies, analog signal source, and other measurement equipment shall be provided by the user.

PCB (unequipped) Texas Instruments LMH730216/NOPB on eBay PCB (unequipped) Texas Instruments LMH730216/NOPB on Amazon

 
 

PCB design board Texas Instruments TLV809KEVM-019

The TLV809KEVM-019 is a fully assembled and tested circuit that allows easy evaluation of TLV809K33 supply voltage supervisor (SVS) at a supply voltage of 3.3V. TLV809K33 is an active low reset SVS. The output (reset) of the EVM will either be high (equivalent to supply voltage) when VDD is greater than the threshold voltage and low (0V) when VDD is less than the threshold voltage.

PCB design board Texas Instruments TLV809KEVM-019 on eBay PCB design board Texas Instruments TLV809KEVM-019 on Amazon

 
 

PCB design board Texas Instruments ADS6124EVM

The ADS6124EVM is a circuit board that allows designers to evaluate the performance of Texas Instrumentsā€˜ ADS6124 device, a low power 12-bit 105 MSPS analog to digital converter. The ADC features a configurable parallel DDR LVDS or CMOS outputs.

PCB design board Texas Instruments ADS6124EVM on eBay PCB design board Texas Instruments ADS6124EVM on Amazon

 
 

PCB design board Texas Instruments TPS2115AEVM-061

The TPS211xA EVM is an evaluation module for the Texas Instruments TPS211xA family of two-input, one-output power multiplexers. These multiplexers enable seamless transition between two power supplies, each operating at 2.8 V5.5 V and delivering up to 1 A. EVM configurations are available for the TPS2110A through TPS2115A.

PCB design board Texas Instruments TPS2115AEVM-061 on eBay PCB design board Texas Instruments TPS2115AEVM-061 on Amazon

 
 

PCB design board Texas Instruments ADS62P15EVM

The ADS62P15 EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments' ADS62P15 device, a dual channel 11-bit 125 MSPS analog to digital converter. The ADC features a user selectable parallel CMOS or DDR LVDS output. Users can use either the TSW1100 (CMOS mode), TSW1400EVM or TSW1405EVM (DDR LVDS mode) to capture the data from the converter.

PCB design board Texas Instruments ADS62P15EVM on eBay PCB design board Texas Instruments ADS62P15EVM on Amazon

 
 

PCB design board Texas Instruments TPS62150EVM-505

The TPS62150EVM-505 (HPA505-003) uses the TPS62150 adjustable version and is set to a 3.3-V output. The EVM operates with full-rated performance with an input voltage between 3.7 V and 17 V. The TPS62150 is a 1-A, synchronous, step-down converter in a 3x3-mm, 16-pin QFN package. Both fixed and adjustable output voltage units are available.

PCB design board Texas Instruments TPS62150EVM-505 on eBay PCB design board Texas Instruments TPS62150EVM-505 on Amazon

 
 

PCB design board Texas Instruments TPS386040EVM

The TPS386040EVM provides the capabilities needed for supervising and sequencing four power supplies, including one negative power supply. The EVM also provides an I2C interface for use with the TI USB-GPIO adapter.

PCB design board Texas Instruments TPS386040EVM on eBay PCB design board Texas Instruments TPS386040EVM on Amazon




Copyright © Bargainplace.uk Inc. All Rights Reserved. In association with Bargainplace.co.uk