PCB design board Texas Instruments SN65LVDS250EVM Stockists

The SN65LVDS250 is a 4 x 4 non-blocking Cross Point switch. Low-Voltage differential signaling (LVDS) is used to achieve signaling rates of greater than 2.0 Gbps per channel. Each output driver includes a 4:1 multiplexer to allow any input to be routed to any output. Internal signal paths are fully differential to achieve the high signaling speed while maintaining low signal skews. The SN65LVDS250 LVDS driver output characteristics are complaint with the requirements of the TIA/EIA-644-A standard.


Bargain Price: £72.99

PCB design board Texas Instruments SN65LVDS250EVM Deals on eBay PCB design board Texas Instruments SN65LVDS250EVM Deals on Amazon
StockistProductPrice 
BargainplacePCB design board Texas Instruments SN65LVDS250EVM£72.99Visit Store


PCB design board Texas Instruments SN65LVDS250EVM Related Products:

 
 

PCB design board Texas Instruments TPS65217BEVM

The TPS65217BEVM is a fully assembled platform for evaluating the performance of the TPS65217B power management device.

PCB design board Texas Instruments TPS65217BEVM on eBay PCB design board Texas Instruments TPS65217BEVM on Amazon

 
 

PCB design board Texas Instruments LM3447-A19-120VEVM

The Texas Instruments LM3447-A19-120VEVM evaluation module (EVM) helps designers evaluate the performance of the LM3447 PFC Flyback Controller for LED Lighting. The EVM is a primary-side power regulated PFC controller used for commercial and residential phase-cut dimmer compatible LED lamp drivers. It uses fixed frequency valley switching operation, resulting in discontinuous current operation.

PCB design board Texas Instruments LM3447-A19-120VEVM on eBay PCB design board Texas Instruments LM3447-A19-120VEVM on Amazon

 
 

PCB design board Texas Instruments TPS51217EVM-533

The TPS51217EVM-533 is a fully assembled and tested circuit for evaluating the TPS51217 Synchronous Step Down Controller. The TPS51217EVM-533 converts VBAT voltage into lower output voltage.

PCB design board Texas Instruments TPS51217EVM-533 on eBay PCB design board Texas Instruments TPS51217EVM-533 on Amazon

 
 

PCB design board Texas Instruments TPS61093EVM-519

The TPS61093EVM-519 facilitates evaluation of the TPS61093 low input, 20V/1.1A step-up DC/DC converter.

PCB design board Texas Instruments TPS61093EVM-519 on eBay PCB design board Texas Instruments TPS61093EVM-519 on Amazon

 
 

PCB design board Texas Instruments CDCE421AEVM

CDCE421AEVM is the evaluation module for CDCE421A. CDCE421A is a highly versatile,

PCB design board Texas Instruments CDCE421AEVM on eBay PCB design board Texas Instruments CDCE421AEVM on Amazon

 
 

PCB design board Texas Instruments TPA711MSOPEVM

A 700-mW mono amplifier that will operate in both bridge-tied load (BTL) and single-ended (SE) modes. This makes the TPA711 ideal for applications that require a mono earphone and speaker. In addition, integrated DEPOP circuitry eliminates speaker noise when the amplifier turns on, off, or exits shutdown. the TPA711 is characterized at 3.3 V and 5 V. Package: 8-pin MSOP PowerPAD.

PCB design board Texas Instruments TPA711MSOPEVM on eBay PCB design board Texas Instruments TPA711MSOPEVM on Amazon

 
 

PCB design board Texas Instruments SERDESUB-21USB/NOPB

The SERDESUB-21USB is an evaluation kit designed to demonstrate performance and capabilities of the DS90UB903Q and DS90UB904Q FPD-Link III Serializer/Deserializer chipset. The chipset enables transmission of a high-speed video data along with a low latency bidirectional control bus over a single twisted pair cable. The integrated control channel transfers data simultaneously over the same serial video link.

PCB design board Texas Instruments SERDESUB-21USB/NOPB on eBay PCB design board Texas Instruments SERDESUB-21USB/NOPB on Amazon

 
 

PCB design board Texas Instruments TPS54428EVM-052

The TPS54428EVM-052 evaluation module (EVM) is a fully assembled and tested circuit for evaluating the TPS54428 Synchronous Step-Down DC-DC Converter with Eco-Mode. The EVM operates from a 4.5V to 18V input and provides a 1.05V output at up to 4A. The main control loop for the EVM uses D-CAP2 mode control, which provides a very fast transient response with no external components.

PCB design board Texas Instruments TPS54428EVM-052 on eBay PCB design board Texas Instruments TPS54428EVM-052 on Amazon

 
 

PCB design board Texas Instruments TL1963A-25EVM

The TL1963A-25EVM facilitates evaluation of the TL1963A-25 1.5A Low-Noise Fast-Transient-Response Low-Dropout Regulator. The EVM allows the user to apply different input voltage levels (2.5V to 20V) and different loads (0 to 1.5A) and check the regulated output voltage for stability.

PCB design board Texas Instruments TL1963A-25EVM on eBay PCB design board Texas Instruments TL1963A-25EVM on Amazon

 
 

PCB design board Texas Instruments THS7320YHCEVM

The THS7320YHCEVM is designed to quickly and easily demonstrate the functionality and versatility of the device. The EVM is ready for power, signal source, and test instruments. The THS7320YHCEVM is configured with a 75 ohm input and output termination.

PCB design board Texas Instruments THS7320YHCEVM on eBay PCB design board Texas Instruments THS7320YHCEVM on Amazon




Copyright © Bargainplace.uk Inc. All Rights Reserved. In association with Bargainplace.co.uk