The DVEVM (Digital Video Evaluation Module) kit will allow you to evaluate TI’s new DaVinciTM Technology and the DM646x architecture. This technology brings together system-solution components tailored for efficient and compelling digital video and audio. The board contains a DaVinci TMS320DM6467 dual-core device with an ARM9 and C64+ DSP for development of applications that use both a general-purpose processor and an accelerated DSP processor.
Bargain Price: £2699.00
The EVM generates 3.3-V and 5-V LDO output from a wide input range of 5.5 V to 28 V. The rated current for each output is 100 mA. The EVM also delivers an always-on 3.3-V, 5 m-A output.
The TPS2480EVM-002 is a fully assembled and tested circuit for evaluating the TPS2480 Positive Voltage, Intelligent Protection Device/Hotswap Controller and I2C Current Monitor.
The TAS5504-5142V4EVM PurePath Digital™ customer evaluation amplifier module demonstrates two audio integrated circuits, TAS5504A and TAS5142, from Texas Instruments (TI). The TAS5504APAG is a high-performance 32-bit (24-bit input) multichannel PurePath Digital™ pulse width modulator (PWM) based on Equibit™ technology, with a fully symmetrical AD modulation scheme. It accepts input sample rates from 32 kHz to 192 kHz. The device also has digital audio processing (DAP) that provides 48-bit signal processing, advanced performance, and a high level of system integration.
The TUSB9261DEMO board is a free-standing reference design that acts as a bridge between a SuperSpeed USB (USB 3.0) bus and a Serial–ATA (SATA) device. The TUSB9261DEMO is used to evaluate system compatibility. It provides a TUSB9261 hardware reference design for connection to a SATA device such as a solid state drive, hard disk drive, DVD drive, or Blu-Ray drive
The TLV803SEVM-019 is a fully assembled and tested circuit that allows easy evaluation of TLV803S supply voltage supervisor (SVS) at a supply voltage of 3.3 V. TLV803S is an active low reset SVS. The output (reset) of the EVM will either be high (equivalent to supply voltage) when VDD is greater than the threshold voltage and low (0-V) when VDD is less than the threshold voltage.
The BQ24156AEVM-697 evaluation module is a complete charger module for evaluating compact, flexible, high-efficiency, USB-friendly, switch-mode charge management solution for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The bq24156A integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package. The charge parameters can be programmed through an I²C interface.
A 700-mW bridge-tied load (BTL) mono amplifier with ultra-low supply current, integrated depop circuitry and diferential inputs. The TPA741 is characterized at 3.3 V and 5 V.
The DV2954S1H Development System provides a development environment for the bq2954 Lithium Ion Fast-Charge IC. The DV2954S1H incorporates a bq2954 and a buck-type switch-mode regulator to provide fast charge control for 1 through 4 Li-Ion cells.
The UCC2897A evaluation module (EVM) is an active clamp reset forward converter providing a 3.3-V regulated output at 30 A of load current, operating from a 48-V input. The design operates over the full 36-V to 72-V telecom input range, and is able to fully regulate down to zero load current. The module uses the UCC2897A Current Mode Active Clamp PWM Controller for effectively demonstrating the active clamp transformer reset technique.
The INA149EVM is a platform for basic functional evaluation of the INA149 High Common-Mode Difference Amplifier