The TPA2017D2RTJEVM allows the engineer to evaluate the TPA2017D2, a stereo, Class-D audio power amplifier with SmartGain™ (AGC/DRC) in a QFN package. The TPA2017D2 has 2 GPIO pins for easy configuration.
Bargain Price: £110.00
| Stockist | Price | |
|---|---|---|
| Bargainplace | £110.00 | Visit Store |
The TPS2411EVM is an Evaluation module set up to wire-OR two power supplies for redundant power to a load using two TPS2411s and MOSFETs.
The LM3150 evaluation boards are designed to provide the design engineer with a fully functional power converter based on Constant On-Time with Emulated Ripple mode control to evaluate the LM3150 and the entire LM315x family of parts. The evaluation board is preconfigured to use the LM3150 with the output voltage adjusted to 3.3V, with a typical max load current of 10A. This board is configured for 250 kHz.
The TSC2301EVM circuit board is a 6 inch by 4 inch platform that contains a 16 position key pad used to exercise the TSC2301 device. The TSC2301 is an advanced touch screen controller, which communicates to a host processor through an SPI serial interface. In addition, a full stereo audio codec is included in the TSC2301, and audio data is communicated to the device over an I2 S bus.
The THS7373EVM is designed to quickly and easily demonstrate the functionality and versatility of the device. The EVM is ready for power, signal source, and test instruments. The EVM is configured with a 75 ohm input and output termination.
The TPS54110EVM-044 evaluation module allows the designer to evaluate the TPS54110 SWIFT DC/DC converter. The module is optimized for small size and uses a small ceramic capacitor and a low profile inductor in the output filter. The input voltage is 3-6V and the output is adjustable down to 0.9V for lower DSP/FPGA core voltages by adjusting a resistor divider.
The LMK04800 family is the industry's highest performance clock conditioner with superior clock jitter cleaning, generation, and distribution with advanced features to meet next generation system requirements. The dual loop PLLatinum™ architecture enables 111 fs rms jitter (12 kHz to 20 MHz) using a low noise VCXO module or sub-200 fs rms jitter (12 kHz to 20 MHz) using a low cost external crystal and varactor diode.
The TPS53313EVM-078 evaluation module (EVM) is a step-down regulator featuring the TPS53313. The TPS53313EVM-078 is designed to use a 12-V voltage rail to produce a regulated 1.2-V output with up to 6-A load current. The TPS53313EVM-078 is designed to demonstrate the TPS53313 in a typical Point-Of-Load (POL) application while providing a number of test points to evaluate the performance of the TPS53313.
The ADS5517EVM is a circuit board that allows designers to evaluate the performance of Texas Instruments‘ ADS5517 device, an 11 bit 200 MSPS analog to digital converter. The circuit board allows for the ability to evaluate the ADS5517 operating in either DDR LVDS output mode or CMOS output mode. An onboard FPGA decodes the ADC output mode and provides the ADC data on a CMOS output header.
The Texas Instruments TPS22980EVM evaluation module (EVM) helps designers evaluate the performance of the TPS22980 MUX with Over-current Limit. The EVM allows for MUX test functionality. By setting Enable signals the designer can switch between Low Power Voltage and High Power Voltage. The current limiting capabilities of the TPS22980 can be tested by setting different resistances with available jumpers.
The Dual-Slot AdvancedMC™ Controller Evaluation Module (TPS2359EVM) is a PCB platform for users to learn about the features and operation of the TPS2359 integrated circuit from Texas Instruments (TI). The TPS2359 Full Featured Dual-Slot AdvancedMC™ Controller manages two 12 V and two 3.3 V power rails, and features inrush and fault current limiting, FET OR’ing, input UVLO protection, logic-level enable inputs and an I²C interface. Current control on the 12 V rails has a high degree of programmability, including independent current limit and fast trip thresholds.