The TPS22932BEVM is an evaluation module for the Texas Instruments family of low-input voltage, ultra-low rON load switches. This EVM operates over a 0.9 V to 3.6 V range and provides a continuous output current of up to 110 mA. Additional open resistor and capacitor footprints allow for the use of customer-selected input and output load values.
Bargain Price: £40.99
The DRV8830 evaluation module consists of a 1A, H-bridge motor driver with a I2C control interface and a small number external components that can be used to drive one brushed DC motor or other loads like solenoids. With the DRV8830EVM, designers can quickly and easily evaluate the performance of DRV8830 motor driver in their specific application. The DRV8830 includes an internal reference voltage which is used to set the PWM regulated output voltage controlled by the VSET bits from the serial interface. This EVM operates on power supply voltages from 2.75 V to 6 V.
The TPA6100A2 is a stereo headphone amplifier capable of delivering 50mW of continuous RMS power per channel into 16-Ohm speakers. The amplifier's gain is externally set by three resistors per input channel.
The TMP104EVM is a platform for evaluating the performance of the TMP104 under various signal, reference, and supply conditions. Four TMP104's are included on the board to demonstrate MDA (Multiple Device Access commands). The included USB interface hardware and software makes evaluation simple; no additional hardware or instruments are required.
The TPS2058AEVM-295 supports the four-channel, current limited power-distribution switch part number TPS2058A. This EVM operates over a 2.7-V to 5.5-V range and provides a continuous output current of up to 0.5A. Test points provide convenient access to all critical node voltages.
The BQ27421EVM-G1A evaluation module is a complete evaluation system for the bq27421. The EVM includes one bq27421 circuit module with an integrated current-sense resistor. A separated orderable EV2300 or EV2400 PC interface board for gas gauge interface along with a PC USB cable, and Windows™-based PC software is needed when using this EVM. The circuit module includes one bq27421 integrated circuit and all other onboard components necessary to monitor and predict capacity for a system-side fuel gauge solution.
The TPS2056AEVM-293 is an evaluation module (EVM) for the Texas Instruments family of two-channel, current-limited, power-distribution switches. This EVM operates over a 2.7 V to 5.5 V range and provide a continuous output current of up to 1.5 A. Test points provide convenient access to all critical node voltages.
The TPS54872EVM-222 kit allows the designer to easily evaluate the TPS54872 synchronous buck DC/DC Converter with integrated 8 A continuous power MOSFETs. The Module is designed for active bus termination applications such as DDR memory, GTL, SSTL, etc. The module is optimized for small size and high frequency and uses ceramic capacitors in the output filter.
The bq24060EVM is an evaluation tool for the bq24060 linear single-cell Li-Ion charger with thermal regulation and input over-voltage protection. The EVM is a complete designed-and-tested charger circuit that allows the user to test all functions of the bq24060 and to charge a single-cell Li-Ion battery with up to 1 A of continuous charge current. The EVM comes with a pre-programmed charge current setting of 0.7 A.
The THS4531ADGKEVM is designed to quickly and easily demonstrate the functionality and versatility of the amplifier. The EVM is ready to connect to power, signal source, and test instruments through the use of on-board connectors. The default amplifier configuration is single-ended input, single-ended output (via transformer), and split supply.
The DEM-OPA-MSOP-2B demonstration fixture helps designers evaluate the operation and performance of TI's dual, high speed, wideband operational amplifiers. This unpopulated PC board is compatible with products offered in the 10-lead MSOP (DGS) package.