The TPS2421-2EVM-03 is a 3 V to 18 V module using the TPS2421-2 hot swap controller with integrated MOSFET. At power on, the output is power limited to control inrush current and protect the MOSFET. On an over-current condition, the controller interrupts power to the load at high speed and signals load status.
Bargain Price: £53.99
The TPS54428EVM-052 evaluation module (EVM) is a fully assembled and tested circuit for evaluating the TPS54428 Synchronous Step-Down DC-DC Converter with Eco-Mode. The EVM operates from a 4.5V to 18V input and provides a 1.05V output at up to 4A. The main control loop for the EVM uses D-CAP2 mode control, which provides a very fast transient response with no external components.
The TPS2552/3DBVEVM and TPS2552/3DRVEVM are evaluation modules (EVM) for Texas Instruments’family of power-distribution switches with adjustable current-limit. These EVMs operate over a 2.5 V to 6.5 V range. An onboard jumper sets the output current-limit to either 0.5 A or 1 A.
The TLV320DAC3203EVM-K is a complete evaluation/demonstration kit for the TLV320DAC3203 audio DAC. The kit includes a TLV320DAC3203EVM, and a USB-based motherboard called the USB-MODEVM Interface board. The TLV320DAC3203EVM-K software, the DAC3203 CS, is an intuitive, easy-to-use, powerful tool to learn, evaluate, and control the TLV320DAC3203. This tool was specifically designed to make learning the TLV320DAC3203 easy.
The TPS61310EVM-638 Evaluation Module (EVM) demonstrates the Texas Instruments TPS61310 LED camera flash and video light driver with I2C interface. The user’s guide describes the characteristics, functions, and use of the TPS61310EVM-638 Evaluation Module This document includes setup instructions, a schematic diagram, a bill of materials and PCB layout drawings for the EVM.
The SIMPLE SWITCHER power module evaluation board is optimized for peak performance and increased flexibility. By incorporating additional ceramic and an aluminum filter capacitor, the power module EVAL board demonstrates the low output ripple, fast transient response, and low conducted and radiated EMI performance of the device. Adjusting the output voltage, optimizing the control loop circuitry, and fine-tuning the filter capacitance is ease, with convenient size and placement of the passive components on the board. Finally, the excellent thermal performance of the power modules is enhanced using a 4-layer 1oz copper PCB.
The new C2000 Experimenter Kits from Texas Instruments are ideal products for OEMs to use for initial device exploration and testing. The 28335 Experimenter Kit has a docking station with access to all controlCARD signals, breadboard areas, RS-232, JTAG connector, and on board USB JTAG emulation. Each kit contains a 28335 controlCARD.
The Texas Instruments TPS43336EVM evaluation module (EVM) helps designers evaluate the operation and performance of the TPS43336 Low Iq, Single Boost, Dual Synchronous Buck Controller.
The LP3878-ADJ is an 800 mA low-dropout linear regulator whose output voltage can be externally set to any value between 1V and 5.5 V using two resistors. This application note gives information about the evaluation board supplied to demonstrate the function of this part. This board is designed to handle either the LP3878MR-ADJ (PSOP-8) or the LP3878SD-ADJ (LLP-8). By default the board is populated with the LP3878MR-ADJ (PSOP-8) device.
This TPS6108xEVM-147 uses either a TPS61080 or TPS61081 boost converter to step up 2.5 V to 6 V input voltages to 12 V. The goal of the EVM is to facilitate evaluation of the TPS61081 power supply solution. The EVM uses the TPS61080 or TPS61081 adjustable
The LM2854 PowerWise® SIMPLE SWITCHER® buck regulator evaluation board is a 500 kHz step-down voltage regulator capable of driving from 0A to 4A load current with excellent power conversion efficiency. The LM2854 TSSOP-16 evaluation board is designed to accept an input voltage rail between 2.95V and 5.5V and deliver a fixed and highly accurate output voltage of 1.2V.