This special evaluation module is intended for TI's Applications Personel, including TI distributor and TI representative applications personel, to evaluate the power management reference designs for Xilinx FPGAs, as seen in the reference design guide downloadable from www.ti.com/xilinxfpga.
Bargain Price: £295.00
This evaluation module (EVM) is a complete evaluation system for the bq3060/bq29412 battery management system. The EVM includes one bq3060/bq29412 circuit module, a PC USB cable, and Windows™-based PC software. The circuit module includes one bq3060 integrated circuit (IC), one bq29412 IC, and all other onboard components necessary to monitor and predict capacity, perform cell balancing, monitor critical parameters, protect the cells from overcharge, over-discharge, short-circuit, and overcurrent in 2-, 3- or 4-series cell Li-ion or Li-polymer battery packs.
The LM5041 evaluation board is designed to provide the design engineer with a fully functional current fed push-pull power converter to evaluate the LM5041 controller, and also the LM5101 buck stage gate driver,in a typical environment.
The TLV320DAC3120EVM-U (ACEV-1A) is a complete evaluation module for the TLV320DAC3120 audio codec. The EVM is supported by TI’s CodecControl software, a block-diagram based graphical user interface for TI audio codec’s.
The DEM-OPA-MSOP-2A demonstration fixture helps designers evaluate the operation and performance of TI's dual, high speed, wideband operational amplifiers. This unpopulated PC board is compatible with products offered in the 8-lead MSOP (DGK) package.
The TPS65185EVM is a fully assembled platform for evaluating the performance of the TPS65186 EINK display driver.
The TSC2301EVM circuit board is a 6 inch by 4 inch platform that contains a 16 position key pad used to exercise the TSC2301 device. The TSC2301 is an advanced touch screen controller, which communicates to a host processor through an SPI serial interface. In addition, a full stereo audio codec is included in the TSC2301, and audio data is communicated to the device over an I2 S bus.
The Texas Instruments TPS712xxEVM-050 dual RF LDO evaluation module (EVM) helps designers evaluate the operation and performance of the TPS712xx family of devices. These devices are tailored to applications that need both high PSRR and low output noise.
The high performance CC3200 is the industry's first single-chip Microcontroller (MCU) with built-in Wi-Fi connectivity for the LaunchPad™ ecosystem. Created for the Internet of Things (IoT), the SimpleLink Wi-Fi CC3200 device is a wireless MCU that integrates a high-performance ARM® Cortex®-M4 MCU allowing customers to develop an entire application with a single IC. With on-chip Wi-Fi, internet and robust security protocols, no prior Wi-Fi experience is needed for faster development.
The LM22672 evaluation board is designed to demonstrate the capabilities of the LM22672 switching regulator. The LM22672 evaluation board is configured to provide an output voltage of 3.3V up to 1A load current with an input voltage range of 4.5V to 42V. Due to the low RDS(ON) of the integrated N-channel MOSFET and maximum duty -cycle limitations, the minimum input voltage of 4.5V will only provide a 3.3V output voltage for load currents up to 500 mA. For load currents higher than 500 mA, an input voltage of 5.5V or higher is required. The typical operating frequency is 500 kHz.
The LM96080EB is the evaluation board for LM96080, a hardware monitor that contains a 10-bit delta-sigma ADC capable of measuring 7 positive voltages and local temperature. The LM96080EB connects via USB to a PC and is controlled by the SensorEval software. SensorEval software allows easy access and control of the LM96080's registers and reports voltage, temperature, and fan outputs.